機械英語詞匯

組裝、沖壓、噴漆等專業詞匯

Assembly line組裝線 
Layout布置圖 
Conveyer流水線物料板 
Rivet table拉釘機 
Rivet gun拉釘槍 
Screw driver起子 
Electric screw driver電動起子 
Pneumatic screw driver氣動起子 
worktable 工作桌 
OOBA開箱檢查 
fit together組裝在一起 
fasten鎖緊(螺絲) 
fixture 夾具(治具) 
pallet棧板 
barcode條碼 
barcode scanner條碼掃描器 
fuse together熔合 
fuse machine熱熔機 
repair修理 
operator作業員 
QC品管 
supervisor 課長 
ME制造工程師 
MT制造生技 
cosmetic inspect外觀檢查 
inner parts inspect內部檢查 
thumb screw大頭螺絲 
lbs. inch鎊、英寸 
EMI gasket導電條 
front plate前板 
rear plate后板 
chassis 基座 
bezel panel面板 
power button電源按鍵 
reset button重置鍵 
Hi-pot test of SPS高源高壓測試 
Voltage switch of SPS 
電源電壓接拉鍵 
sheet metal parts 沖件 
plastic parts塑膠件 
SOP制造作業程序 
material check list物料檢查表 
work cell工作間 
trolley臺車 
carton紙箱 
sub-line支線 
left fork叉車 
production department生產部門 
planning department企劃部 
QC Section品管科 
stamping factory沖壓廠 
painting factory烤漆廠 
molding factory成型廠 
common equipment常用設備 
uncoiler and straightener整平機 
punching machine 沖床 
robot機械手 
hydraulic machine油壓機 
lathe車床 
planer |'plein?|刨床 
miller銑床 
grinder磨床 
driller銑床 
linear cutting線切割 
electrical sparkle電火花 
welder電焊機 
staker=reviting machine鉚合機 
position職務 
president董事長 
general manager總經理 
special assistant manager特助 
factory director廠長 
department director部長 
deputy manager | =vice manager副理 
section supervisor課長 
deputy section supervisor =vice section superisor副課長 
group leader/supervisor組長 
line supervisor線長 
assistant manager助理 
to move, to carry, to handle搬運 
be put in storage入庫 
pack packing包裝 
to apply oil擦油 
to file burr 銼毛刺 
final inspection終檢 
to connect material接料 
to reverse material 翻料 
wet station沾濕臺 
Tiana天那水 
cleaning cloth抹布 
to load material上料 
to unload material卸料 
to return material/stock to退料 
scraped |'skr?pid|報廢 
scrape ..v.刮;削 
deficient purchase來料不良 
manufacture procedure制程 
deficient manufacturing procedure制程不良 
oxidation |' ksi'dei?n|氧化 
scratch刮傷 
dents壓痕 
defective upsiding down抽芽不良 
defective to staking鉚合不良 
embedded lump鑲塊 
feeding is not in place送料不到位 
stamping-missing漏沖 
production capacity生產力 
education and training教育與訓練 
proposal improvement提案改善 
spare parts=buffer備件 
forklift叉車 
trailer=long vehicle拖板車 
compound die合模 
die locker鎖模器 
pressure plate=plate pinch壓板 
bolt螺栓 
name of a department部門名稱 
administration/general affairs dept總務部 
automatic screwdriver電動啟子 
thickness gauge厚薄規 
gauge(or jig)治具 
power wire電源線 
buzzle蜂鳴器 
defective product label不良標簽 
identifying sheet list標示單 
screwdriver holder起子插座 
pedal踩踏板 
stopper阻擋器 
flow board流水板 
hydraulic handjack油壓板車 
forklift叉車 
pallet棧板 
glove(s)手套 
glove(s) with exposed fingers割手套 
thumb大拇指 
forefinger食指 
midfinger中指 
ring finger無名指 
little finger小指 
band-aid創可貼 
iudustrial alcohol工業酒精 
alcohol container沾濕臺 
head of screwdriver起子頭 
sweeper掃把 
mop拖把 
vaccum cleaner吸塵器 
rag 抹布 
garbage container灰箕 
garbage can垃圾箱 
garbage bag垃圾袋 
chain鏈條 
jack升降機 
production line流水線 
chain鏈條槽 
magnetizer加磁器 
lamp holder燈架 
to mop the floor拖地 
to clean the floor掃地 
to clean a table擦桌子 
air pipe 氣管 
packaging tool打包機 
packaging打包 
missing part漏件 
wrong part錯件 
excessive defects過多的缺陷 
critical defect極嚴重缺陷 
major defect主要缺陷 
minor defect次要缺陷 
not up to standard不合規格 
dimension/size is a little bigger尺寸偏大(小) 
cosmetic defect外觀不良 
slipped screwhead/slippery screw head螺絲滑頭 
slipped screwhead/shippery screw thread滑手 
speckle斑點 
mildewed=moldy=mouldy發霉 
rust生銹 
deformation變形 
burr(金屬)flash(塑件)毛邊 
poor staking鉚合不良 
excesssive gap間隙過大 
grease/oil stains油污 
inclusion雜質 
painting peel off臟污 
shrinking/shrinkage縮水 
mixed color雜色 
scratch劃傷 
poor processing 制程不良 
poor incoming part事件不良 
fold of pakaging belt打包帶折皺 
painting make-up補漆 
discoloration羿色 
water spots水漬 
polishing/surface processing表面處理 
exposed metal/bare metal金屬裸露 
lack of painting烤漆不到位 
safety安全 
quality品質 
delivery deadline交貨期 
cost成本 
engineering工程 
die repair模修 
enterprise plan = enterprise expansion projects企劃 
QC品管 
die worker模工 
production, to produce生產 
equipment設備 
to start a press開機 
stop/switch off a press關機 
classification整理 
regulation整頓 
cleanness清掃 
conservation清潔 
culture教養 
qualified products, up-to-grade products良品 
defective products, not up-to-grade products不良品 
waste廢料 
board看板 
feeder送料機 
sliding rack滑料架 
defective product box不良品箱 
die change 換模 
to fix a die裝模 
to take apart a die拆模 
to repair a die修模 
packing material包材 
basket蝴蝶竺 
plastic basket膠筐 
isolating plate baffle plate; barricade隔板 
carton box紙箱 
to pull and stretch拉深 
to put material in place, to cut material, to input落料 
to impose lines壓線 
to compress, compressing壓縮 
character die字模 
to feed, feeding送料 
transportation運輸 
(be)qualfied, up to grade合格 
not up to grade, not qualified不合格 
material change, stock change材料變更 
feature change 特性變更 
evaluation評估 
prepare for, make preparations for 準備 
parameters參數 
rotating speed, revolution轉速 
manufacture management制造管理 
abnormal handling異常處理 
production unit生產單位 
lots of production生產批量 
steel plate鋼板 
roll material卷料 
manufacture procedure制程 
operation procedure作業流程 
to revise, modify修訂 
to switch over to, switch---to throw--over switching over切換 
engineering, project difficulty 
工程瓶頸 
stage die工程模 
automation自動化 
to stake, staking, reviting鉚合 
add lubricating oil加潤滑油 
shut die架模 
shut height of a die架模高度 
analog-mode device類模器 
die lifter舉模器 
argon welding氬焊 
vocabulary for stamping 
沖壓常詞匯 
stamping, press沖壓 
punch press, dieing out press沖床 
uncoiler & strainghtener整平機 
feeder送料機 
rack, shelf, stack料架 
cylinder油缸 
robot機械手 
taker取料機 
conveyer belt輸送帶 
transmission rack輸送架 
top stop上死點 
bottom stop下死點 
one stroke一行程 
inch寸動 
to continue, cont.連動 
to grip(material)吸料 
location lump, locating piece, block stop 定位塊 
reset復位 
smoothly順利 
dent壓痕 
scratch刮傷 
deformation變形 
filings鐵削 
to draw holes抽孔 
inquiry, search for查尋 
to stock, storage, in stock庫存 
receive領取 
approval examine and verify審核 
processing, to process加工 
delivery, to deliver 交貨 
to return delivenry to. 
to send delinery back 
to retrn of goods退貨 
registration登記 
registration card登記卡 
to control管制 
to put forward and hand in提報 
safe stock安全庫存 
acceptance = receive驗收 
to notice通知 
application form for purchase請購單 
consume, consumption消耗 
to fill in填寫 
abrasion磨損 
reverse angle = chamfer倒角 
character die字模 
to collect, to gather收集 
failure, trouble故障 
statistics統計 
demand and supply需求 
career card履歷卡 
to take apart a die卸下模具 
to load a die裝上模具 
to tight a bolt擰緊螺栓 
to looser a bolt擰松螺栓 
to move away a die plate移走模板 
easily damaged parts易損件 
standard parts標準件 
breaking.(be)broken,(be)cracked 斷裂 
to lubricate潤滑 
common vocabulary for die engineering 
模具工程常用詞匯 
die 模具 
figure file, chart file圖檔 
cutting die, blanking die沖裁模 
progressive die, follow (-on)die 
連續模 
compound die復合模 
punched hole沖孔 
panel board鑲塊 
to cutedges=side cut=side scrap切邊 
to bending折彎 
to pull, to stretch拉伸 
Line streching, line pulling線拉伸 
engraving, to engrave刻印 
upsiding down edges翻邊 
to stake鉚合 
designing, to design設計 
design modification設計變化 
die block模塊 
folded block折彎塊 
sliding block滑塊 
location pin定位銷 
lifting pin頂料銷 
die plate, front board模板 
padding block墊塊 
stepping bar墊條 
upper die base上模座 
lower die base下模座 
upper supporting blank上承板 
upper padding plate blank上墊板 
spare dies模具備品 
spring 彈簧 
bolt螺栓 
document folder文件夾 
file folder資料夾 
to put file in order整理資料 
spare tools location手工備品倉 
first count初盤人 
first check初盤復棹人 
second count 復盤人 
second check復盤復核人 
equipment設備 
waste materials廢料 
work in progress product在制品 
casing = containerazation裝箱 
quantity of physical invetory second count 復盤點數量 
quantity of customs count 
會計師盤,點數量 
the first page第一聯 
filed by accounting department for reference會計部存查 
end-user/using unit(department)使用單位 
summary of year-end physical inventory bills 
年終盤點截止單據匯總表 
bill name單據名稱 
This sheet and physical inventory list will be sent to accounting 
department together (Those of NHK will be sent to financial 
department) 
本表請與盤點清冊一起送會計部－(NHK廠區送財會部) 
Application status records of year-end physical inventory List and 
physical inventory card 年終盤點卡與清冊使用－狀況明細表 
blank and waste sheet NO. 
空白與作廢單號 
plate電鍍 
mold成型 
material for engineering mold testing工程試模材料 
not included in physical inventory不列入盤點 
sample樣品 
incoming material to be inspected進貨待驗 
description品名 
steel/rolled steel鋼材 
material statistics sheet 
物料統計明細表 
meeting minutes會議記錄 
meeting type 會別 
distribution department分發單位 
location地點 
chairman主席 
present members出席人員 
subject主題 
conclusion結論 
decision items決議事項 
responsible department負責單位 
pre-fixed finishing date預定完成日 
approved by / checked by / prepared by核準/審核/承辦 
PCE assembly production schedule sheet 
PCE組裝廠生產排配表 
model機鍾 
work order工令 
revision版次 
remark備注 
production control confirmation生產確認 
checked by初審 
approved by核準 
department部門 
stock age analysis sheet 
庫存貨齡分析表 
on-hand inventory現有庫存 
available material良品可使用 
obsolete material良品已呆滯 
to be inspected or reworked 
待驗或重工 
total合計 
cause description原因說明 
part number/ P/N 料號 
type形態 
item/group/class類別 
quality品質 
prepared by制表 
notes說明 
year-end physical inventory difference analysis sheet 
年終盤點差異分析表 
physical inventory盤點數量 
physical count quantity帳面數量 
difference quantity差異量 
cause analysis原因分析 
raw materials原料 
materials物料 
finished product成品 
semi-finished product半成品 
packing materials包材 
good product/accepted goods/ accepted parts/good parts良品 
defective product/non-good parts不良品 
disposed goods處理品 
warehouse/hub倉庫 
on way location在途倉 
oversea location海外倉 
spare parts physical inventory list備品盤點清單 
spare molds location模具備品倉 
skid/pallet棧板 
tox machine自鉚機 
wire EDM線割 
EDM放電機 
coil stock卷料 
sheet stock片料 
tolerance工差 
score=groove壓線 
cam block滑塊 
pilot導正筒 
trim剪外邊 
pierce剪內邊 
drag form壓鍛差 
pocket for the punch head掛鉤槽 
slug hole廢料孔 
feature die公母模 
expansion dwg展開圖 
radius半徑 
shim(wedge)楔子 
torch-flame cut火焰切割 
set screw止付螺絲 
form block折刀 
stop pin定位銷 
round pierce punch=die button圓沖子 
shape punch=die insert異形子 
stock locater block定位塊 
under cut=scrap chopper清角 
active plate活動板 
baffle plate擋塊 
cover plate蓋板 
male die公模 
female die母模 
groove punch壓線沖子 
air-cushion eject-rod氣墊頂桿 
spring-box eject-plate彈簧箱頂板 
bushing block襯套 
insert 入塊 
club car高爾夫球車 
capability能力 
parameter參數 
factor系數 
phosphate皮膜化成 
viscosity涂料粘度 
alkalidipping脫脂 
main manifold主集流脈 
bezel斜視規 
blanking穿落模 
dejecting頂固模 
demagnetization去磁;消磁 
high-speed transmission高速傳遞 
heat dissipation熱傳 
rack上料 
degrease脫脂 
rinse水洗 
alkaline etch齡咬 
desmut剝黑膜 
D.I. rinse純水次 
Chromate鉻酸處理 
Anodize陽性處理 
seal封孔 
revision版次 
part number/P/N料號 
good products良品 
scraped products報放心品 
defective products不良品 
finished products成品 
disposed products處理品 
barcode條碼 
flow chart流程表單 
assembly組裝 
stamping沖壓 
molding成型 
spare parts=buffer備品 
coordinate座標 
dismantle the die折模 
auxiliary fuction輔助功能 
poly-line多義線 
heater band 加熱片 
thermocouple熱電偶 
sand blasting噴沙 
grit 砂礫 
derusting machine除銹機 
degate打澆口 
dryer烘干機 
induction感應 
induction light感應光 
response=reaction=interaction感應 
ram連桿 
edge finder巡邊器 
concave凸 
convex凹 
short射料不足 
nick缺口 
speck瑕?? 
shine亮班 
splay 銀紋 
gas mark焦痕 
delamination起鱗 
cold slug冷塊 
blush 導色 
gouge溝槽;鑿槽 
satin texture段面咬花 
witness line證示線 
patent專利 
grit沙礫 
granule=peuet=grain細粒 
grit maker抽粒機 
cushion緩沖 
magnalium鎂鋁合金 
magnesium鎂金 
metal plate鈑金 
lathe車 
mill銼 
plane刨 
grind磨 
drill鋁 
boring鏜 
blinster氣泡 
fillet鑲;嵌邊 
through-hole form通孔形式 
voller pin formality滾針形式 
cam driver鍘楔 
shank摸柄 
crank shaft曲柄軸 
augular offset角度偏差 
velocity速度 
production tempo生產進度現狀 
torque扭矩 
spline=the multiple keys花鍵 
quenching淬火 
tempering回火 
annealing退火 
carbonization碳化 
alloy合金 
tungsten high speed steel鎢高速的 
moly high speed steel鉬高速的 
organic solvent有機溶劑 
bracket小磁導 
liaison聯絡單 
volatile揮發性 
resistance電阻 
ion離子 
titrator滴定儀 
beacon警示燈 
coolant冷卻液 
crusher破碎機 
模具工程類 
plain die簡易模 
pierce die沖孔模 
forming die成型模 
progressive die連續模 
gang dies復合模 
shearing die剪邊模 
riveting die鉚合模 
pierce沖孔 
forming成型(抽凸,沖凸) 
draw hole抽孔 
bending折彎 
trim切邊 
emboss凸點 
dome凸圓 
semi-shearing半剪 
stamp mark沖記號 
deburr or coin壓毛邊 
punch riveting沖壓鉚合 
side stretch側沖壓平 
reel stretch卷圓壓平 
groove壓線 
blanking下料 
stamp letter沖字(料號) 
shearing剪斷 
tick-mark nearside正面壓印 
tick-mark farside反面壓印 
沖壓名稱類 
extension dwg展開圖 
procedure dwg工程圖 
die structure dwg模具結構圖 
material材質 
material thickness料片厚度 
factor系數 
upward向上 
downward向下 
press specification沖床規格 
die height range適用模高 
die height閉模高度 
burr毛邊 
gap間隙 
weight重量 
total wt.總重量 
punch wt.上模重量 
五金零件類 
inner guiding post內導柱 
inner hexagon screw內六角螺釘 
dowel pin固定銷 
coil spring彈簧 
lifter pin頂料銷 
eq-height sleeves=spool等高套筒 
pin銷 
lifter guide pin浮升導料銷 
guide pin導正銷 
wire spring圓線彈簧 
outer guiding post外導柱 
stop screw止付螺絲 
located pin定位銷 
outer bush外導套 
模板類 
top plate上托板（頂板） 
top block上墊腳 
punch set上模座 
punch pad上墊板 
punch holder上夾板 
stripper pad脫料背板 
up stripper上脫料板 
male die公模(凸模) 
feature die公母模 
female die母模(凹模) 
upper plate上模板 
lower plate下模板 
die pad下墊板 
die holder下夾板 
die set下模座 
bottom block下墊腳 
bottom plate下托板(底板) 
stripping plate內外打(脫料板) 
outer stripper外脫料板 
inner stripper內脫料板 
lower stripper下脫料板 
零件類 
punch沖頭 
insert入塊(嵌入件) 
deburring punch壓毛邊沖子 
groove punch壓線沖子 
stamped punch字模沖子 
round punch圓沖子 
special shape punch異形沖子 
bending block折刀 
roller滾軸 
baffle plate擋塊 
located block定位塊 
supporting block for location 
定位支承塊 
air cushion plate氣墊板 
air-cushion eject-rod氣墊頂桿 
trimming punch切邊沖子 
stiffening rib punch = stinger 加強筋沖子 
ribbon punch壓筋沖子 
reel-stretch punch卷圓壓平?jīng)_子 
guide plate定位板 
sliding block滑塊 
sliding dowel block滑塊固定塊 
active plate活動板 
lower sliding plate下滑塊板 
upper holder block上壓塊 
upper mid plate上中間板 
spring box彈簧箱 
spring-box eject-rod彈簧箱頂桿 
spring-box eject-plate彈簧箱頂板 
bushing bolck襯套 
cover plate蓋板 
guide pad導料塊 
塑件&模具相關英文 
compre sion molding壓縮成型 
flash mold溢流式模具 
plsitive mold擠壓式模具 
split mold分割式模具 
cavity型控 母模 
core模心 公模 
taper錐拔 
leather cloak仿皮革 
shiver飾紋 
flow mark流痕 
welding mark溶合痕 
post screw insert螺紋套筒埋值 
self tapping screw自攻螺絲 
striper plate脫料板 
piston活塞 
cylinder汽缸套 
chip細碎物 
handle mold手持式模具 
移轉成型用模具 
encapsulation molding低壓封裝成型 
射出成型用模具 
two plate兩極式（模具） 
well type蓄料井 
insulated runner絕緣澆道方式 
hot runner熱澆道 
runner plat澆道模塊 
valve gate閥門澆口 
band heater環帶狀的電熱器 
spindle閥針 
spear head刨尖頭 
slag well冷料井 
cold slag冷料渣 
air vent排氣道 
h=0.02~0.05mm 
w=3.2mm 
L=3~5mm 
welding line熔合痕 
eject pin頂出針 
knock pin頂出銷 
return pin回位銷反頂針 
sleave套筒 
stripper plate脫料板 
insert core放置入子 
runner stripper plate澆道脫料板 
guide pin導銷 
eject rod (bar)（成型機）頂業捧 
subzero深冷處理 
three plate三極式模具 
runner system澆道系統 
stress crack應力電裂 
orientation定向 
sprue gate射料澆口，直澆口 
nozzle射嘴 
sprue lock pin料頭鉤銷(拉料桿) 
slag well冷料井 
side gate側澆口 
edge gate側緣澆口 
tab gate搭接澆口 
film gate薄膜澆口 
flash gate閘門澆口 
slit gate縫隙澆口 
fan gate扇形澆口 
dish gate因盤形澆口 
H=F=1/2t~1/5t 
T=2.5~3.5mm 
diaphragm gate隔膜澆口 
ring gate環形澆口 
subarine gate潛入式澆口 
tunnel gate隧道式澆口 
pin gate針點澆口 
Φ0.8~1.0mm 
Runner less無澆道 
(sprue less)無射料管方式 
long nozzle延長噴嘴方式 
sprue澆口;溶渣

品質人員名稱類 
QC quality control 品質管理人員 
FQC final quality control 終點品質管制人員 
IPQC in process quality control 制程中的品質管制人員 
OQC output quality control 最終出貨品質管制人員 
IQC incoming quality control 進料品質管制人員 
TQC total quality control 全面質量管理 
POC passage quality control 段檢人員 
QA quality assurance 質量保證人員 
OQA output quality assurance 出貨質量保證人員 
QE quality engineering 品質工程人員 
品質保證類 
FAI first article inspection 新品首件檢查 
FAA first article assurance 首件確認 
TVR tool verification report 模具確認報告 
3B 3B 模具正式投產前確認 
CP capability index 能力指數 
CPK capability index of process 模具制程能力參數 
SSQA standardized supplier quality 合格供應商品質評估 
OOBA out of box audit 開箱檢查 
QFD quality function deployment 品質機能展開 
FMEA failure model effectiveness analysis 失效模式分析 
8 disciplines 8項回復內容 
FA final audit 最後一次稽核 
CAR corrective action request 改正行動要求 
corrective action report 改正行動報告 
FQC運作類 
AQL Acceptable Quality Level 運作類允收品質水準 
S/S Sample size 抽樣檢驗樣本大小 
ACC Accept 允收 
REE Reject 拒收 
CR Critical 極嚴重的 
MAJ Major 主要的 
MIN Minor 輕微的 
AOQ Average Output Quality 平均出廠品質 
AOQL Average Output Quality Level 平均出廠品質 
Q/R/S Quality/Reliability/Service 品質/可靠度服務 
MIL-STD Military-Standard 軍用標準 
S I-S IV Special I-Special IV 特殊抽樣水準等級 
P/N Part Number 料號 
L/N Lot Number 特采 
AOD Accept On Deviation 特采 
UAI Use As It 首件檢查報告 
FPIR First Piece Inspection Report 百萬分之一 
PPM Percent Per Million 批號 
制程統計品管專類 
SPC Statistical Process Control 統計制程管制 
SQC Statistical Quality Control 統計品質管制 
R Range 全距 
AR Averary Range 全距平均值 
UCL Upper Central Limit 管制上限 
LCL Lower Central Limit 管制下限 
MAX Maximum 最大值 
MIN Minimum 最小值 
GRR Gauge Reproducibility&Repeatability 量具之再制性及重測性判斷量可靠與否 
DIM Dimension 尺寸 
DIA Diameter 直徑 
FREQ Frequency 頻率 
N Number 樣品數 
其它品質術語類 
QCC Quality Control Circle 品質圈 
QIT Quality Improvement Team 品質改善小組 
PDCA Plan Do Check Action 計劃 執行 檢查 總結 
ZD Zero Defect 零缺點 
QI Quality Improvement 品質改善 
QP Quality Policy 目標方針 
TQM Total Quality Management 全面品質管理 
MRB Material Reject Bill 退貨單 
LQL Limiting Quality Level 最低品質水準 
RMA Return Material Audit 退料認可 
QAN Quality Amelionrate Notice 品質改善活動 
ADM Absolute Dimension Measuremat 全尺寸測量 
QT Quality Target 品質目標 
7QCTools 7 Quality Controll Tools 品管七大手法 
通用之件類 
ECN Engineering Change Notes 工程變更通知(供應商) 
ECO Engineering Change Order 工程改動要求(客戶) 
PCN Process Change Notice 工序改動通知 
PMP Product Management Plan 生產管制計劃 
SIP Specification In Process 制程檢驗規格 
SOP Standard Operation Procedure 制造作業規范 
IS Inspection Specification 成品檢驗規范 
BOM Bill Of Material 物料清單 
PS Package Specification 包裝規范 
SPEC Specification 規格 
DWG Drawing 圖面 
系統文件類 
QC Quality System 品質系統 
ES Engineering Standarization 工程標準 
CGOO China General PCE龍華廠文件 
H Huston (美國)休斯敦 
C Compaq (美國)康伯公司 
C China 中國大陸 
A Assembly 組裝(廠) 
S Stamping 沖壓(廠) 
P Painting 烤漆(廠) 
I Intel 英特爾公司 
T TAIWAN 臺灣 
IWS International Workman Standard 工藝標準 
ISO International Standard Organization 國際標準化組織 
GS General Specification 一般規格 
CMCS C-China M-Manufact C-Compaq S-Stamping Compaq產品在龍華沖壓廠制造作業規范 
CQCA Q-Quality A-Assembly Compaq產品在龍華組裝廠品管作業規范 
CQCP P-Painting Compaq產品在龍華烤漆廠品管作業規范 
部類 
PMC Production & Material Control 生產和物料控制 
PPC Production Plan Control 生產計劃控制 
MC Material Control 物料控制 
ME Manafacture Engineering 制造工程部 
PE Project Engineering 產品工程部 
A/C Accountant Dept 會計部 
P/A Personal & Administration 人事行政部 
DC Document Center 資料中心 
QE Quality Engineering 品質工程(部) 
QA Quality Assurance 品質保證(處) 
QC Quality Control 品質管制(課) 
PD Product Department 生產部 
LAB Labratry 實驗室 
IE Industrial Engineering 工業工程 
R&D Research & Design 設計開發部 
P Painting 烤漆(廠) 
A Asssembly 組裝(廠) 
S Stamping 沖壓(廠) 
生產類 
PCS Pieces 個(根,塊等) 
PRS Pairs 雙(對等) 
CTN Carton 卡通箱 
PAL Pallet/skid 棧板 
PO Purchasing Order 采購訂單 
MO Manufacture Order 生產單 
D/C Date Code 生產日期碼 
ID/C Identification Code (供應商)識別碼 
SWR Special Work Request 特殊工作需求 
L/N Lot Number 批號 
P/N Part Number 料號 
其它 
OEM Original Equipment Manufacture 原設備制造 
PCE Personal Computer Enclosure 個人電腦外設 
PC Personal Computer 個人電腦 
CPU Central Processing Unit 中央處理器 
SECC SECC` 電解片 
SGCC SGCC 熱浸鍍鋅材料 
NHK North of Hongkong 中國大陸 
PRC People's Republic of China 中國大陸 
U.S.A the United States of America 美國 
A.S.A.P As Soon As Possible 盡可能快的 
E-MAIL Electrical-Mail 電子郵件 
N/A Not Applicable 不適用 
QTY Quantity 數量 
VS 以及 
REV Revision 版本 
JIT Just In Time 零庫存 
I/O Input/Output 輸入/輸出 
OK Ok 好 
NG Not Good 不行,不合格 
C=0 Critical=0 極嚴重不允許 
ESD Electry-static Discharge 靜電排放 
5S 希臘語 整理,整頓,清掃,清潔,教養 
ATIN Attention 知會 
CC Carbon Copy 副本復印相關人員 
APP Approve 核準,認可,承認 
CHK Check 確認 
AM Ante Meridian 上午 
PM Post Meridian 下午 
CD Compact Disk 光碟 
CD-ROM Compact Disk Read-Only Memory 只讀光碟 
FDD Floppy Disk Drive 軟碟機 
HDD Hard Disk Drive 碟碟機 
REF Reference 僅供參考 
CONN Connector 連接器 
CAV Cavity 模穴 
CAD Computer Aid Design 計算機輔助設計 
ASS'Y Assembly 裝配,組裝 
MAT'S Material 材料 
IC Integrated Circuit 集成電路 
T/P True Position 真位度 
TYP Type 類型 
WDR Weekly Delivery Requitement 周出貨需求 
C?T Cycle Time 制程周期 
L/T Lead Time 前置時間(生產前準備時間) 
S/T Standard Time 標準時間 
P/M Product Market 產品市場 
3C Computer,Commumcation,Consumer electronic's 消費性電子 
5WIH When,Where,Who,What,Why,How to 
5M Man,Machine,Material,Method,Measurement 
4MIH Man,Materia,Money,Method,Time 人力,物力,財務,技術,時間(資源) 
SQA Strategy Quality Assurance 策略品質保證 
DQA Desigh Quality Assurance 設計品質保證 
MQA Manufacture Quality Assurance 制造品質保證 
SSQA Sales and service Quality Assurance 銷售及服務品質保證 
LRR Lot Rejeet Rate 批退率 
BS Brain storming 腦力激蕩 
EMI Electronic Magnetion Inspect 高磁測試 
FMI Frequency Modulatim Inspect 高頻測試 
B/M Boar/Molding(flat cable) 
C/P Connector of PC 
A/P Assembly 
SPS Switching power supply 電源箱 
DT Desk Top 臥式(機箱) 
MT Mini-Tower 立式(機箱) 
DVD Digital Vedio Disk 
VCD Vdeio Compact Disk 
LCD Liquid Crystal Display 
CAD Computer AID Design 
CAM Computer AID Manufacturing 
CAE Computer AID Engineering 
ABIOS Achanced Basic in put/output system 先進的基本輸入/輸出系統 
CMOS Complemeruary Metoll Oxide Semiconductor 互補金屬氧化物半導體 
PDA Personal Digital Assistant 個人數字助理 
IC Integrated Circuit 集成電路 
ISA Industry Standard Architecture 工業標準體制結構 
MCA Micro Channel Architecture 微通道結構 
EISA Extended Industry Standard Architecture 擴充的工業標準結構 
SIMM Single in-line memory module 單項導通匯流組件 
DIMM Dual in-line Memory Module 雙項導通匯流組件 
LED Light-Emitting Diode 發光二級管 
FMEA Failure Mode Effectivenes 失效模式分析 
W/H Wire Harness 金屬線緒束集組件 
F/C Flat Calle 排線 
PCB Printed Circuit Board 印刷電路板 
CAR Correction Action Report 改善報告 
NG Not Good 不良 
WPR Weekly Delivery Requirement 周出貨要求 
PPM Parts Per Million 百萬分之一 
TPM Total Production Maintenance 全面生產保養 
MRP Material Requiremcnt Planning 物料需計劃 
OC Operation System 作業系統 
TBA To Be Design 待定,定缺 
D/C Drawing Change 
P/P Plans & Procedune 
EMI Electrical-Music Industry 電子音樂工業 
RFI Read Frequency Input 讀頻輸入 
MMC Maximum Material Condition 
MMS Maximum Material Size 
LMC Least Material Condition 
LMS Least Material Size

模具技術用語 
各種模具常用成形方式 
accurate die casting 精密壓鑄 
powder forming 粉末成形 
calendaring molding 壓延成形 
powder metal forging 粉末鍛造 
cold chamber die casting 冷式壓鑄 
precision forging 精密鍛造 
cold forging 冷鍛 
press forging 沖鍛 
compacting molding 粉末壓出成形 
rocking die forging 搖動鍛造 
compound molding 復合成形 
rotary forging 回轉鍛造 
compression molding 壓縮成形 
rotational molding 離心成形 
dip mold 浸漬成形 
rubber molding 橡膠成形 
encapsulation molding 注入成形 
sand mold casting 砂模鑄造 
extrusion molding 擠出成形 
shell casting 殼模鑄造 
foam forming ?泡成形 
sinter forging 燒結鍛造 
forging roll 軋鍛 
six sides forging 六面鍛造 
gravity casting 重力鑄造 
slush molding 凝塑成形 
hollow(blow) molding 中空(吹出)成形 
squeeze casting 高壓鑄造 
hot chamber die casting 熱室壓鑄 
swaging 擠鍛 
hot forging 熱鍛 
transfer molding 轉送成形 
injection molding 射出成形 
warm forging 溫鍛 
investment casting 精密鑄造 
matched die method 對模成形法 
laminating method 被覆淋膜成形 
low pressure casting 低壓鑄造 
lost wax casting 脫蠟鑄造 
matched mould thermal forming 對模熱成形模

各式模具分類用語 
bismuth mold 鉍鑄模 
landed plunger mold 有肩柱塞式模具 
burnishing die 擠光模 
landed positive mold 有肩全壓式模具 
button die 鑲?cè)胧綀A形凹模 
loading shoe mold 料套式模具 
center-gated mold 中心澆口式模具 
loose detail mold 活零件模具 
chill mold 冷硬用鑄模 
loose mold 活動式模具 
clod hobbing 冷擠壓制模 
ouvering die 百葉窗沖切模 
composite dies 復合模具 
manifold die 分歧管模具 
counter punch 反凸模 
modular mold 組合式模具 
double stack mold 雙層模具 
multi-cavity mold 多模穴模具 
electroformed mold 電鑄成形模 
multi-gate mold 復式澆口模具 
expander die 擴徑模 
offswt bending die 雙折冷彎模具 
extrusion die 擠出模 
palletizing die 疊層模 
family mold 反套制品模具 
plaster mold 石膏模 
blank through dies 漏件式落料模 
porous mold 通氣性模具 
duplicated cavity plate 復板模 
positive mold 全壓式模具 
fantail die 扇尾形模具 
pressure die 壓緊模 
fishtail die 魚尾形模具 
profile die 輪廓模 
flash mold 溢料式模具 
progressive die 順序模 
gypsum mold 石膏鑄模 
protable mold 手提式模具 
hot-runner mold 熱流道模具 
prototype mold 雛形試驗?zāi)＞?nbsp;
ingot mold 鋼錠模 
punching die 落料模 
lancing die 切口模 
raising(embossing) 壓花起伏成形 
re-entrant mold 倒角式模具 
sectional die 拼合模 
runless injection mold 無流道冷料模具 
sectional die 對合模具 
segment mold 組合模 
semi-positive mold 半全壓式模具 
shaper 定型模套 
single cavity mold 單腔模具 
solid forging die 整體鍛模 
split forging die 拼合鍛模 
split mold 雙并式模具 
sprueless mold 無注道殘料模具 
squeezing die 擠壓模 
stretch form die 拉伸成形模 
sweeping mold 平刮鑄模 
swing die 振動模具 
three plates mold 三片式模具 
trimming die 切邊模 
unit mold 單元式模具 
universal mold 通用模具 
unscrewing mold 退扣式模具 
yoke type die 軛型模

模具廠常用之標準零配件 
air vent vale 通氣閥 anchor pin 錨梢 
angular pin 角梢 baffle 調節阻板 
angular pin 傾斜梢 baffle plate 折流檔板 
ball button 球塞套 ball plunger 定位球塞 
ball slider 球塞滑塊 binder plate 壓板 
blank holder 防皺壓板 blanking die 落料沖頭 
bolster 上下模板 bottom board 澆注底板 
bolster 墊板 bottom plate 下固定板 
bracket 托架 bumper block 緩沖塊 
buster 堵口 casting ladle 澆注包 
casting lug 鑄耳 cavity 模穴(模仁) 
cavity retainer plate 模穴托板 center pin 中心梢 
clamping block 鎖定塊 coil spring 螺旋彈簧 
cold punched nut 冷沖螺母 cooling spiral 螺旋冷卻栓 
core 心型 core pin 心型梢 
cotter 開口梢 cross 十字接頭 
cushion pin 緩沖梢 diaphragm gate 盤形澆口 
die approach 模頭料道 die bed 型底 
die block 塊形模體 die body 鑄模座 
die bush 合模襯套 die button 沖模母模 
die clamper 夾模器 die fastener 模具固定用零件 
die holder 母模固定板 die lip 模唇 
die plate 沖模板 die set 沖壓模座 
direct gate 直接澆口 dog chuck 爪牙夾頭 
dowel 定位梢 dowel hole 導套孔 
dowel pin 合模梢 dozzle 輔助澆口 
dowel pin 定位梢 draft 拔模錐度 
draw bead 張力調整桿 drive bearing 傳動軸承 
ejection pad 頂出襯墊 ejector 脫模器 
ejector guide pin 頂出導梢 ejector leader busher 頂出導梢襯套 
ejector pad 頂出墊 ejector pin 頂出梢 
ejector plate 頂出板 ejector rod 頂出桿 
ejector sleeve 頂出襯套 ejector valve 頂出閥 
eye bolt 環首螺栓 filling core 椿入蕊 
film gate 薄膜形澆口 finger pin 指形梢 
finish machined plate 角形模板 finish machined round plate 圓形模板 
fixed bolster plate 固定側模板 flanged pin 帶凸緣? 
flash gate 毛邊形澆口 flask 上箱 
floating punch 浮動沖頭 gate 澆口 
gate land 澆口面 gib 凹形拉緊? 
goose neck 鵝頸管 guide bushing 引導襯套 
guide pin 導梢 guide post 引導柱 
guide plate 導板 guide rail 導軌 
head punch 頂?沖頭 headless punch 直柄沖頭 
heavily tapered solid 整體模蕊盒 hose nippler 管接頭 
impact damper 緩沖器 injection ram 壓射柱塞 
inlay busher 嵌入襯套 inner plunger 內柱塞 
inner punch 內沖頭 insert 嵌件 
insert pin 嵌件梢 king pin 轉向梢 
king pin bush 主梢襯套 knockout bar 脫模杵 
land 合模平坦面 land area 合模面 
leader busher 導梢襯套 lifting pin 起模頂? 
lining 內襯 locating center punch 定位中心沖頭 
locating pilot pin 定位導梢 locating ring 定位環 
lock block 壓塊 locking block 定位塊 
locking plate 定位板 loose bush 活動襯套 
making die 打印沖子 manifold block 歧管檔塊 
master plate 靠模樣板 match plate 分型板 
mold base 塑膠模座 mold clamp 鑄模緊固夾 
mold platen 模用板 moving bolster 換模保持裝置 
moving bolster plate 可動側模板 one piece casting 整體鑄件 
parallel block 平行墊塊 paring line 分模線 
parting lock set 合模定位器 pass guide 穴型導板 
peened head punch 鑲?cè)胧經_頭 pilot pin 導? 
pin gate 針尖澆口 plate 襯板 
pre extrusion punch 頂擠沖頭 punch 沖頭 
puncher 推桿 pusher pin 襯套梢 
rack 機架 rapping rod 起模桿 
re-entrant mold 凹入模 retainer pin 嵌件梢 
retainer plate 托料板 return pin 回位梢 
riding stripper 浮動脫模器 ring gate 環型澆口 
roller 滾筒 runner 流道 
runner ejector set 流道頂出器 runner lock pin 流道拉梢 
screw plug 頭塞 set screw 固定螺絲 
shedder 脫模裝置 shim 分隔片 
shoe 模座之上下模板 shoot 流道 
shoulder bolt 肩部螺絲 skeleton 骨架 
slag riser 冒渣口 slide(slide core) 滑塊 
slip joint 滑配接頭 spacer block 間隔塊 
spacer ring 間隔環 spider 模蕊支架 
spindle 主軸 sprue 注道 
sprue bushing 注道襯套 sprue bushing guide 注道導套 
sprue lock bushing 注道定位襯套 sprue puller 注道拉料? 
spue line 合模線 square key 方鍵 
square nut 方螺帽 square thread 方螺紋 
stop collar 限位套 stop pin 止動梢 
stop ring 止動環 stopper 定位停止梢 
straight pin 圓柱? stripper bolt 脫料螺栓 
stripper bushing 脫模襯套 stripper plate 剝料板 
stroke end block 行程止梢 submarine gate 潛入式澆口 
support pillar 支撐支柱/頂出支柱 support pin 支撐梢 
supporting plate 托板 sweep templete 造模刮板 
tab gate 輔助澆口 taper key 推拔鍵 
taper pin 拔錐梢/錐形梢 teeming 澆注 
three start screw 三條螺紋 thrust pin 推力銷 
tie bar 拉杵 tunnel gate 隧道形澆口 
vent 通氣孔 wortle plate 拉絲模板

模具常用之工作機械 
3D coordinate measurement 三次元量床 boring machine 搪孔機 
cnc milling machine CNC銑床 contouring machine 輪廓鋸床 
copy grinding machine 仿形磨床 copy lathe 仿形車床 
copy milling machine 仿形銑床 copy shaping machine 仿形刨床 
cylindrical grinding machine 外圓磨床 die spotting machine 合模機 
drilling machine ?孔機 engraving machine 雕刻機 
engraving E.D.M. 雕模放置加工機 form grinding machine 成形磨床 
graphite machine 石墨加工機 horizontal boring machine 臥式搪孔機 
horizontal machine center 臥式加工制造中心 internal cylindrical machine 內圓磨床

jig boring machine 冶具搪孔機 jig grinding machine 冶具磨床 
lap machine 研磨機 machine center 加工制造中心 
multi model miller 靠磨銑床 NC drilling machine NC鉆床 
NC grinding machine NC磨床 NC lathe NC車床 
NC programming system NC程式制作系統 planer 龍門刨床 
profile grinding machine 投影磨床 projection grinder 投影磨床 
radial drilling machine 旋臂?床 shaper 牛頭刨床 
surface grinder 平面磨床 try machine 試模機 
turret lathe 轉塔車床 universal tool grinding machine 萬能工具磨床 
vertical machine center 立式加工制造中心 wire E.D.M. 線割放電加工機

檢驗量測工具用語 
autocollimator 自動準直機 bench comparator 比長儀 
block gauge 塊規 bore check 精密小測定器 
calibration 校準 caliper gauge 卡規 
check gauge 校對規 clearance gauge 間隙規 
clinoretee 測斜儀 comparator 比測儀 
cylinder square 圓筒直尺 depth gauge 測深規 
dial indicator 針盤指示表 dial snap gauge 卡規 
digital micrometer 數位式測微計 feeler gauge 測隙規 
gauge plate 量規定位板 height gauge 測高規 
inside calipers 內卡鉗 inside micrometer 內分??卡 
interferometer 干涉儀 leveling block 平臺 
limit gauge 限規 micrometer 測微計 
mil 千分之一寸 monometer 壓力計 
morse taper gauge 莫氏錐度量規 nonius 游標卡尺 
optical flat 光學平晶 optical parallel 光學平行 
passimeter 內徑儀 position scale 位置刻度 
profile projector 輪廓光學投影儀 protractor 分角器 
radius 半徑 ring gauge 環規 
sine bar 正弦量規 snap gauge 卡模 
square master 直角尺 stylus 觸針 
telescopic gauge 伸縮性量規 working gauge 工作量規

模具鋼材 
alloy tool steel 合金工具鋼 aluminium alloy 鋁合金鋼 
bearing alloy 軸承合金 blister steel 浸碳鋼 
bonderized steel sheet 邦德防蝕鋼板 carbon tool steel 碳素工具鋼 
clad sheet 被覆板 clod work die steel 冷鍛模用鋼 
emery 金鋼砂 ferrostatic pressure 鋼鐵水靜壓力 
forging die steel 鍛造模用鋼 galvanized steel sheet 鍍鋅鐵板 
hard alloy steel 超硬合金鋼 high speed tool steel 高速度工具鋼 
hot work die steel 熱鍛模用鋼 low alloy tool steel 特殊工具鋼 
low manganese casting steel 低錳鑄鋼 marging steel 馬式體高強度熱處理鋼 
martrix alloy 馬特里斯合金 meehanite cast iron 米漢納鑄鋼 
meehanite metal 米漢納鐵 merchant iron 市售鋼材 
molybdenum high speed steel 鉬系高速鋼 molybdenum steel 鉬鋼 
nickel chromium steel 鎳鉻鋼 prehardened steel 頂硬鋼 
silicon steel sheet 矽鋼板 stainless steel 不銹鋼 
tin plated steel sheet 鍍錫鐵板 tough pitch copper 韌銅 
troostite 吐粒散鐵 tungsten steel ?鋼 
vinyl tapped steel sheet 塑膠覆面鋼板

表面處理關連用語 
age hardening 時效硬化 ageing 老化處理 
air hardening 氣體硬化 air patenting 空氣韌化 
annealing 退火 anode effect 陽極效應 
anodizing 陽極氧化處理 atomloy treatment 阿托木洛伊表面 
austempering 奧氏體等溫淬火 austenite 奧斯田體/奧氏體 
bainite 貝氏體 banded structure 條紋狀組織 
barrel plating 滾鍍 barrel tumbling 滾筒打光 
blackening 染黑法 blue shortness 青熟脆性 
bonderizing 磷酸鹽皮膜處理 box annealing 箱型退火 
box carburizing 封箱滲碳 bright electroplating 輝面電鍍 
bright heat treatment 光輝熱處理 bypass heat treatment 旁路熱處理 
carbide 炭化物 carburized case depth 浸碳硬化深層 
carburizing 滲碳 cementite 炭化鐵 
chemical plating 化學電鍍 chemical vapor deposition 化學蒸鍍 
coarsening 結晶粒粗大化 coating 涂布被覆 
cold shortness 低溫脆性 comemtite 滲碳體 
controlled atmosphere 大氣熱處理 corner effect 銳角效應 
creeping discharge 蠕緩放電 decarburization 脫碳處理 
decarburizing 脫碳退火 depth of hardening 硬化深層 
diffusion 擴散 diffusion annealing 擴散退火 
electrolytic hardening 電解淬火 embossing 壓花 
etching 表面蝕刻 ferrite 肥粒鐵 
first stage annealing 第一段退火 flame hardening 火焰硬化 
flame treatment 火焰處理 full annealing 完全退火 
gaseous cyaniding 氣體氧化法 globular cementite 球狀炭化鐵 
grain size 結晶粒度 granolite treatment 磷酸溶液熱處理 
graphitizing 石墨退火 hardenability 硬化性 
hardenability curve 硬化性曲線 hardening 硬化 
heat treatment 熱處理 hot bath quenching 熱浴淬火 
hot dipping 熱浸鍍 induction hardening 高周波硬化 
ion carbonitriding 離子滲碳氮化 ion carburizing 離子滲碳處理 
ion plating 離子電鍍 isothermal annealing 等溫退火 
liquid honing 液體噴砂法 low temperature annealing 低溫退火 
malleablizing 可鍛化退火 martempering 麻回火處理 
martensite 馬氏體/硬化鐵炭 metallikon 金屬噴鍍法 
metallizing 真空涂膜 nitriding 氮化處理 
nitrocarburizing 軟氮化 normalizing 正�；� 
oil quenching 油淬化 overageing 過老化 
overheating 過熱 pearlite 針尖組織 
phosphating 磷酸鹽皮膜處理 physical vapor deposition 物理蒸鍍 
plasma nitriding 離子氮化 pre-annealing 預備退火 
precipitation 析出 precipitation hardening 析出硬化 
press quenching 加壓硬化 process annealing 制程退火 
quench ageing 淬火老化 quench hardening 淬火 
quenching crack 淬火裂痕 quenching distortion 淬火變形 
quenching stress 淬火應力 reconditioning 再調質 
recrystallization 再結晶 red shortness 紅熱脆性 
residual stress 殘留應力 retained austenite 殘留奧 
rust prevention 防蝕 salt bath quenching 鹽浴淬火 
sand blast 噴砂處理 seasoning 時效處理 
second stage annealing 第二段退火 secular distortion 經年變形 
segregation 偏析 selective hardening 部分淬火 
shot blast 噴丸處理 shot peening 珠擊法 
single stage nitriding 等溫滲氮 sintering 燒結處理 
soaking 均熱處理 softening 軟化退火 
solution treatment 固溶化熱處理 spheroidizing 球狀化退火 
stabilizing treatment 安定化處理 straightening annealing 矯直退火 
strain ageing 應變老化 stress relieving annealing 應力消除退火 
subzero treatment 生冷處理 supercooling 過冷 
surface hardening 表面硬化處理 temper brittleness 回火脆性 
temper colour 回火顏色 tempering 回火 
tempering crack 回火裂痕 texture 咬花 
thermal refining 調質處理 thermoechanical treatment 加工熱處理 
time quenching 時間淬火 transformation 變態 
tufftride process 軟氮化處理 under annealing 不完全退火 
vacuum carbonitriding 真空滲碳氮化 vacuum carburizing 真空滲碳處理 
vacuum hardening 真空淬火 vacuum heat treatment 真空熱處理 
vacuum nitriding 真空氮化 water quenching 水淬火 
wetout 浸潤處理

焊接用語 
acetylene 乙炔 ampere 電流安培 
angle welding 角焊 arc 電弧 
argon arc welding 氬弧焊接 bare electrode 光熔接條 
butt welding 對接焊接 camber 電弧彎曲 
cascade 階疊熔接法 clad weld 被覆熔接 
crator 焊疤 excess metal 多余金屬 
filler rod 焊條 fillet weld 填角焊接 
gas shield 氣體遮蔽 groove welding 起槽熔接 
hand face shield 手握面罩 hard facing 硬表面堆焊 
jig welding 工模焊接 laser beam welding 雷射光焊接 
metal electrode insert gas welding MIG熔接 nugget 點焊熔核 
overlaying 堆焊 peening of welding 珠擊熔接法 
plug welding 塞孔熔接 positioned welding 正向熔接 
pressure welding 壓焊 propane gas cutting 丙烷氣切割 
pure nickel electrode 純鎳熔接條 reinforcement of weld 加強焊接 
resist 抗蝕護膜 root running 背面熔接 
seam 焊縫 seaming 接合 
seam welding 流縫熔接 series seam welding 串聯縫熔接 
skip welding process 跳焊法 spark 火花 
spot welding 點焊接 stitch welding 針角焊接 
stud arc welding 電弧焊接 under laying 下部焊層 
void 焊接空隙 weld flow mark 焊接流痕 
weld flush 焊縫凸起 weld line 焊接紋 
weld mark 焊接痕 weld penetration 熔接透入 
weld zone 焊接區 welding 焊接 
welding bead 焊接泡 welding direction 焊接方向 
welding distortion 焊接變形 welding flux 焊劑 
welding ground 電熔接地 welding interval 焊接周期 
welding stress 熔接應變 welding torch 熔接氣炬

射出成形關聯用語 
activator 活化劑 bag moulding 氣胎施壓成形 
bonding strength 黏合強度 breathing 排氣 
caulking compound 填隙料 cell 氣孔 
cold slug 半凝式射出 colorant 著色劑 
color matching 調色 color masterbatch 色母料 
compound 混合料 copolymer 共聚合體 
cull 殘料廢品 cure 凝固化 
cryptometer 不透明度儀 daylight 開隙 
dry cycle time 空料試車周期時間 ductility 延性 
elastomer 彈性體 extruded bead sealing 壓出粒涂層法 
feed 供料 filler 充填劑 
film blowing 薄膜吹制法 floating platen 活動模板 
foaming agent 發泡劑 gloss 光澤 
granule 顆粒料 gunk 料斗 
hot mark 熱斑 hot stamping 燙印 
injection nozzle 射出噴嘴 injection plunger 射出柱塞 
injection ram 射出沖柱 isomer 同分異構物 
kneader 混合機 leveling agent 勻涂劑 
lubricant 潤滑劑 matched die method 配合成形法 
mould clamping force 鎖模力 mould release agent 脫模劑 
nozzle 噴嘴 oriented film 取向薄膜 
parison 吹氣成形壞料 pellet 粒料 
plasticizer 可塑劑 plunger 壓料柱塞 
porosity 孔隙率 post cure 後固化 
premix 預混料 purging 清除 
reciprocating screw 往復螺桿 resilience 回彈性 
resin injection 樹脂射出法 rheology 流變學 
sheet 塑膠片 shot 注射 
shot cycle 射出循環 slip agent 光滑劑 
take out device 取料裝置 tie bar 拉桿 
toggle type mould clamping system 肘桿式鎖模裝置 
torpedo spreader 魚雷形分流板 transparency 透明性 
void content 空洞率

塑膠原料 
acrylic 壓克力 casein 酪素 
cellulose acetate 醋酸纖維素CA cellulose acetate butyrate 醋酸丁酸纖維素CAB 
composite material 復合材料 cresol resin 甲酚樹脂CF 
dially phthalate 苯二甲酸二烯丙酯 disperse reinforcement 分散性強化復合材料 
engineering plastics 工程塑膠 epoxy resin 環氧樹脂EP 
ethyl cellulose 乙基纖維素 ethylene vinylacetate copolymer 乙烯-醋酸乙烯EVA 
ethylene-vinlacetate copolyme 醋酸乙烯共聚物EVA expanded polystyrene 
?泡聚苯乙烯EPS 
fiber reinforcement 纖維強化熱固性/纖維強化復合材料 
high density polyethylene 高密度聚乙烯HDPE 
high impact polystyrene 高沖擊聚苯乙烯HIPS 
high impact polystyrene rigidity 高沖擊性聚苯乙烯 
low density polyethylene 低密度聚乙烯LDPE melamine resin 三聚氰胺酚醛樹脂MF 
nitrocellulose 硝酸纖維素 phenolic resin 酚醛樹脂 
plastic 塑膠 polyacrylic acid 聚丙烯酸PAP 
polyamide 耐龍PA polybutyleneterephthalate 聚對苯二甲酸丁酯PBT 
polycarbonate 聚碳酸酯PC polyethyleneglycol 聚乙二醇PFG 
polyethyleneoxide 聚氧化乙烯PEO polyethyleneterephthalate 聚乙醇對苯PETP 
polymetylmethacrylate 聚甲基丙烯酸甲酯PMMA polyoxymethylene 聚縮醛POM 
polyphenylene oxide 聚硫化亞苯 polyphenyleneoxide 聚苯醚PPO 
polypropylene 聚丙烯PP polystyrene 聚苯乙烯PS 
polytetrafluoroethylene 聚四氟乙烯PTFE polytetrafluoroethylene 聚四氟乙烯 
polythene 聚乙烯PE polyurethane 聚氨基甲酸酯PU 
polyvinylacetate 聚醋酸乙烯PVAC polyvinylalcohol 聚乙烯醇PVA 
polyvinylbutyral 聚乙烯醇縮丁醛PVB polyvinylchloride 聚氯乙烯PVC 
polyvinylfuoride 聚氟乙烯PVF polyvinylidenechloride 聚偏二氯乙烯PVDC 
prepolymer 預聚物 silicone resin 矽樹脂 
thermoplastic 熱塑性 thermosetting 熱固性 
thermosetting plastic 塑膠 unsaturated polyester 不飽和聚酯樹脂

成形不良用語 
aberration 色差 atomization ?化 
bank mark ?料紋 bite 咬入 
blacking hole 涂料孔(鑄疵) blacking scab 涂料疤 
blister 起泡 blooming 起霜 
blow hole 破孔 blushing 泛白 
body wrinkle 側壁皺紋 breaking-in 冒口帶肉 
bubble 膜泡 burn mark 糊斑 
burr 毛邊 camber 翹曲 
cell 氣泡 center buckle 表面中部波皺 
check 細裂痕 checking 龜裂 
chipping 修整表面缺陷 clamp-off 鑄件凹痕 
collapse 塌陷 color mottle 色斑 
corrosion 腐蝕 crack 裂痕 
crazing 碎裂 crazing 龜裂 
deformation 變形 edge 切邊碎片 
edge crack 裂邊 fading 退色 
filler speak 填充料斑 fissure 裂紋 
flange wrinkle 凸緣起皺 flaw 刮傷 
flow mark 流痕 galling 毛邊 
glazing 光滑 gloss 光澤 
grease pits 污斑 grinding defect 磨痕 
haircrack 發裂 haze 霧度 
incrustation 水銹 indentation 壓痕 
internal porosity 內部氣孔 mismatch 偏模 
mottle 斑點 necking 縮頸 
nick 割痕 orange peel 橘皮狀表面缺陷 
overflow 溢流 peeling 剝離 
pit 坑 pitting corrosion 點狀腐蝕 
plate mark 模板印痕 pock 麻點 
pock mark 痘斑 resin streak 樹脂流紋 
resin wear 樹脂脫落 riding 凹陷 
sagging 松垂 saponification 皂化 
scar 疤痕 scrap 廢料 
scrap jam 廢料阻塞 scratch 刮傷/劃痕 
scuffing 深沖表面劃傷 seam 裂痕 
shock line 模口擠痕 short shot 充填不足 
shrinkage pool 凹孔 sink mark 凹痕 
skin inclusion 表皮摺疊 straightening 矯直 
streak 條狀痕 surface check 表面裂痕 
surface roughening 橘皮狀表皮皺摺 surging 波動 
sweat out 冒汗 torsion 扭曲 
warpage 翹曲 waviness 波痕 
webbing 熔塌 weld mark 焊痕 
whitening 白化 wrinkle 皺紋

模具常用刀具與工作法用語 
adjustable spanner 活動扳手 angle cutter 角銑刀 
anvil 鐵? arbour 心軸 
backing 襯墊 belt sander 帶式打磨機 
buffing 拋光 chamfering machine 倒角機 
chamfering tool 去角刀具 chisel 扁鏨 
chuck 夾具 compass 兩角規 
concave cutter 凹面銑刀 convex cutter 凸形銑刀 
cross joint 十字接頭 cutting edge clearance 刃口余隙角 
drill stand 鉆臺 edge file 刃用銼刀 
file 銼刀 flange joint 凸緣接頭 
grinder 砂輪機 hammer 鐵錘 
hand brace 手搖鉆 hatching 剖面線 
hexagon headed bolt 六角頭螺栓 hexagon nut 六角螺帽 
index head 分度頭 jack 千斤頂 
jig 治具 kit 工具箱 
lapping 研磨 metal saw 金工鋸 
nose angle 刀角 pinchers 鉗子 
pliers 鋏鉗 plug 柱塞頭 
polisher 磨光器 protable driller 手提鉆孔機 
punch 沖頭 sand paper 砂紙 
scraper 刮刀 screw driver 螺絲起子 
scribing 劃線 second out file 中紋銼 
spanner 扳手 spline broach 方栓槽拉刀 
square 直角尺 square sleeker 方形鏝刀 
square trowel 直角度 stripping 剝離工具 
T-slot T形槽 tool for lathe 車刀 
tool point angle 刀刃角 tool post 刀架 
tosecan 劃線盤 trimming 去毛邊 
waffle die flattening 壓紋效平 wiper 脫模鉗 
wrench 螺旋扳手

電腦關聯用語 
3D modeling 三次元模擬 access 通路 
animation 卡通影片 application 應用 
board 基板 bug 故障 
bus 匯流排 CAD 電腦輔助設計 
CAE 電腦輔助工程分析 CAM 電腦輔助制造 
cassette 卡座 color display 彩色顯示器 
command 指令 communication 通信 
compact 精簡小型 computer 電腦 
copy 復制 cursor 游標 
curve modeling 曲面模擬 database 資料庫 
design 設計 digitizing 數位化 
disk 磁碟 dot 點 
eyelet 眼孔 floppy 磁碟片 
format 格式化 graphic 圓解 
hardware 硬體 honeycomb 蜂巢 
interface 界面 know how 秘訣 
laser printer 雷射印表機 lay out 布置 
memory 記憶 memory swap 交換記憶 
microprocessor 微處理器 modeling 造型 
module 模組 monitor 螢?zāi)?nbsp;
mouse 滑鼠 need 需求 
network 網路 new version 新版 
on line 上線中 option 選擇 
PC 個人電腦 plotter 繪圖機 
program 程式 scanning 掃描 
simulation 模擬 software 軟體 
solid model 實體模型 system 系統 
tape 磁帶 terminal 終端機 
texture 構造 trim 修邊 
venter 排氣風扇 word processor 文書處理器

各種沖模加工關連用語 
barreling 滾光加工 belling 壓凸加工 
bending 彎曲加工 blanking 下料加工 
bulging 撐壓加工 burring 沖緣加工 
cam die bending 凸輪彎曲加工 caulking ?合加工 
coining 壓印加工 compressing 壓縮加工 
compression bending 押彎曲加工 crowning 凸面加工 
curl bending 卷邊彎曲加工 curling 卷曲加工 
cutting 切削加工 dinking 切斷蕊骨 
double shearing 疊板裁斷 drawing 引伸加工 
drawing with ironing 抽引光滑加工 embossing 浮花壓制加工 
extrusion 擠制加工 filing 銼削加工 
fine blanking 精密下料加工 finish blanking 光制下料加工 
finishing 精整加工 flanging 凸緣加工 
folding 折邊彎曲加工 folding 摺疊加工 
forming 成形加工 impact extrusion 沖擊擠壓加工 
indenting 壓痕加工 ironing 引縮加工 
knurling 滾花 lock seaming 固定接合 
louvering 百葉窗板加工 marking 刻印加工 
necking 頸縮加工 notching 沖口加工 
parting 分?jǐn)嗉庸?piercing 沖孔加工 
progressive bending 連續彎曲加工 progressive blanking 連續下料加工 
progressive drawing 連續引伸加工 progressive forming 連續成形加工 
reaming 鉸孔加工 restriking 二次精沖加工 
riveting ?接加工 roll bending 滾筒彎曲加工 
roll finishing 滾壓加工 rolling 壓延加工 
roughing 粗加工 scrapless machining 無廢料加工 
seaming 折彎重疊加工 shaving 缺口修整加工 
shearing 切斷加工 sizing 精壓加工/矯正加工 
slitting 割縫加工 spinning 卷邊?接 
staking ?固 stamping 鍛壓加工 
swaging 擠鍛壓加工 trimming 整緣加工 
upsetting 鍛粗加工 wiring 抽線加工

沖壓機械及周邊關連用語 
back shaft 支撐軸 blank determination 胚料展開 
bottom slide press 下傳動式壓力機 board drop hammer 板落錘 
brake 煞車 buckle 剝砂面 
camlachie cramp 鑄包 casting on flat ?合 
chamotte sand 燒磨砂 charging hopper 加料漏斗 
clearance 間隙 closed-die forging 合模鍛造 
clump 夾緊 clutch 離合器 
clutch brake 離合器制動器 clutch boss 離合器輪殼 
clutch lining 離合器覆蓋 coil car 帶卷升降運輸機 
coil cradle 卷材進料裝置 coil reel stand 鋼材卷料架 
column 圓柱 connection screw 連桿調節螺釘 
core compound 砂心黏結劑 counter blow hammer 對擊鍛錘 
cradle 送料架 crank 曲柄軸 
crankless 無曲柄式 cross crank 橫向曲軸 
cushion 緩沖 depression 外縮凹孔 
dial feed 分度送料 die approach �？诮嵌� 
die assembly 合模 die cushion 模具緩沖墊 
die height 沖壓閉合高度 die life 模具壽命 
die opening 母模逃孔 die spotting press 調整沖模用壓力機 
double crank press 雙曲柄軸沖床 draght angle 逃料傾斜角 
edging 邊鍛伸 embedded core 加裝砂心 
feed length 送料長度 feed level 送料高度 
filling core 埋入砂心 filling in 填砂 
film play 液面花紋 fine blanking press 精密下料沖床 
forging roll 輥鍛機 finishing slag 煉後熔渣 
fly wheel 飛輪 fly wheel brake 飛輪制動器 
foot press 腳踏沖床 formboard 進模口板 
frame 床身機架 friction 摩擦 
friction brake 摩擦煞車 gap shear 凹口剪床 
gear 齒輪 gib 滑塊引導部 
gripper 夾具 gripper feed 夾持進料 
gripper feeder 夾緊傳送裝置 hammer 槌機 
hand press 手動沖床 hand rack pinion press 手動齒輪齒條式?jīng)_床 
hand screw press 手動螺旋式?jīng)_床 hopper feed 料斗送料 
idle stage 空站 inching 微調尺寸 
isothermal forging 恒溫鍛造 key clutch 鍵槽離合器 
knockout 脫模裝置 knuckle mechanic 轉向機構 
land 模具直線刀面部 level 水平 
loader 供料器 unloader 卸料機 
loop controller 閉回路控制器 lower die 下模 
micro inching device 微寸動裝置 microinching equipment 微動裝置 
motor 馬達 moving bolster 活動工作臺 
notching press 沖缺口壓力機 opening 排料逃孔 
overload protection device 防超載裝置 pinch roll 導正滾輪 
pinion 小齒輪 pitch 節距 
pressfit 壓入 progressive 連續送料 
pusher feed 推桿式送料 pusher feeder 料片押片裝置 
quick die change system 快速換模系統 regrinding 再次研磨 
releasing 松釋動作 reversed blanking 反轉下料 
robot 機器人 roll forming machine 輥軋成形 
roll forming machine 輥軋成形機 roll release 脫輥 
roller feed 輥式送料 roller leveler 輥式矯直機 
rotary bender 卷彎成形機 safety guard 安全保護裝置 
scrap cutter 廢料切刀 scrap press 廢料沖床 
seamless forging 無縫鍛造 separate 分離 
shave 崩砂 shear angle 剪角 
sheet loader 薄板裝料機 shot 單行程工作 
shrinkage fit 收縮配合 shut height 閉合高度 
sieve mesh 篩孔 sintering of sand 鑄砂燒貼 
slide balancer 滑動平衡器 slug hole 逃料孔 
spin forming machine 旋壓成形機 spotting 合模 
stack feeder 堆疊撥送料機 stickness 黏模性 
straight side frame 沖床側板 stretcher leveler 拉伸矯直機 
strip feeder 料材送料裝置 stripping pressure 彈出壓力 
stroke 沖程 take out device 取料裝置 
toggle press 肘桿式壓力機 transfer 傳送 
transfer feed 連續自動送料裝置 turrent punch press 轉塔沖床 
two speed clutch 雙速離合器 uncoiler 閉卷送料機 
unloader 卸載機 vibration feeder 振動送料機 
wiring press 嵌線卷邊機

線切割放電加工關連用語 
abnormal glow 不規則輝光放電 arc discharge 電弧放電 
belt 皮帶 centreless 無心 
chrome bronze 銘銅 clearance angle 後角 
corner shear drop 直角壓陷 deflection 橈曲度 
discharge energy 放電能量 dressing 修整 
dwell 保壓 flange 凸緣 
gap 間隙 graphite 石墨 
graphite contraction allowance 電極縮小余量 graphite holder 電極夾座 
hair crack 發裂 horn 電極臂 
jump 跳刀 magnetic base 磁性座 
master graphite 標準電極 pipe graphite 管狀電極 
pulse 脈沖 rib working 肋部加工 
roller electrode 滾輪式電極 rotary surface 旋轉面 
shank 柄部 sharp edge 銳角部 
tough bronze 韌銅 traverse 搖臂 
tungsten bronze ?青銅 waviness 波形起伏 
work 工件 working allowance 加工余量 
working dischard 加工廢料

鍛鑄造關連用語 
accretion 爐瘤 acid converter 酸性轉爐 
acid lining cupola 酸性熔鐵爐 acid open-hearth furnace 酸性平爐 
aerator 松砂機 air set mold 常溫自硬鑄模 
airless blasting cleaning 離心噴光 all core molding 集合式鑄模 
all round die holder 通用模座 assembly mark 鑄造合模記號 
back pouring 補澆注 backing sand 背砂 
base bullion 粗金屬錠 base permeability 原砂透氣度 
belling 壓凸 billet 壞料 
bleed 漏鑄 blocker 預鍛模膛 
blocking 粗胚鍛件 blow hole 鑄件氣孔 
board drop hammer 板落錘 bottom pour mold 底澆 
bottom pouring 底注 boxless mold 脫箱砂模 
break-off core 縮頸砂心 brick molding 砌箱造模法 
buckle 剝砂面 camber 錯箱 
camlachie cramp 鑄包 cast blade 鑄造葉片 
casting flange 鑄造凸緣 casting on flat 水平鑄造 
chamotte sand 燒磨砂 charging hopper 加料漏斗 
cleaning of casting 鑄件清理 closed-die forging 合模鍛造 
core compound 砂心黏結劑 core template 砂心模板 
core vent 砂蕊排氣孔 corner gate 壓邊澆口 
counter blow hammer 對擊鍛造 counter lock 止口鑲嵌方式 
depression 外縮凹孔 die approach �？诮嵌� 
draw out 鍛造拔長 draw plate 起模板 
draw spike 起模長針 dummying 預鍛 
embedded core 加裝砂心 erosion 沖砂 
fettling 鑄件清理 filling core 埋入砂心 
filling in 填砂 film play 液面花紋 
finishing slag 煉後熔渣 flash gutter 鍛模飛邊槽 
flask molding 砂箱造模 forging roll 輥鍛機 
formboard 進�？诎� gutter 鍛模飛邊槽 
hammer man 鍛工 heading machine 頂鐓機 
impacter 臥式鍛造機 inblock cast 整體鑄造 
ingot 鑄錠 ingot blank 鑄坯 
inlay casting 鑲鑄法 investment casting 失模鑄造 
isothermal forging 恒溫鍛造 loose piece 木�；顗K 
molding pit 鑄模地坑 pouring process 澆注法 
recasting 重鑄 roll forging 軋鍛 
rolled surface 軋制表面 rough sand 粗砂 
roughing forge 粗鍛 sand crushing 塌箱 
seamless forging 無縫鍛造 separate 分離 
shave 崩砂 shrinkage fit 收縮配合 
shut height 閉合高度 sieve mesh 篩孔 
sintering of sand 鑄砂燒貼 slag 熔渣 
slag inclusion 夾渣 stickness 黏模性 
strip layout 帶狀胚料排樣法 tap casting 頂注 
top gate 頂注澆口 unworked casting 不加工鑄件 
upender 翻轉裝置 upending 頂鍛 
uphill casting 底鑄 white cast iron 白口鑄件

模具加工方法 
barrel 滾筒(加工) bending 波紋加工 
broaching 拉刀切削 centering 定中心 
cutting 切削 cylindrical lathe cutting 外圓車削 
electric discharge machine 放電加工 electrolytic grinding 電解研磨 
embossing 壓花加工 facing 面車削 
filing 銼刀修潤 hand finishing 手工修潤 
hemming 卷邊加工 hobbing 滾齒加工 
joggling 搖動加工 lapping 拋光/研磨修潤 
laser beam machining 雷射加工 lathe cutting 車床車削 
planning 刨削加工 polishing 拋亮光 
reaming 鉸孔修潤 rough machining 粗切削 
rounding 圓形加工 sawing 鋸削 
scaling 清除鋼碇缺陷 shaping 成形加工 
skiving 表面研磨 slotting 切縫切削 
taper turning 錐度車削 thread cutting 螺紋切削 
ultrasonic machining 超音波加工 up cut milling 逆銑加工

學理實驗與試驗用語 
air permeability test 透氣性試驗 austenitic steel 沃斯田鐵鋼 
brinell hardness 布耐內爾硬度 brinell hardness test 布氏硬度試驗 
charpy impact test 夏比沖擊試驗 conical cup test 圓錐杯突試驗 
cup flow test 杯模式流動度試驗 dart drop impact test 落錘沖擊試驗 
Elmendorf test 埃羅門多撕裂強度試驗 environmental stress cracking test 
環境應力龜裂試驗 
ericessen test 埃留伸薄板拉伸試驗 falling ball impact test 落球沖擊試驗 
fatigue test 疲勞試驗 ferrite 純鐵體 
gantt chart 甘特圖 heat cycle test 熱循環試驗 
histogram 柱狀圖 hot bend test 熱彎試驗 
izod impact test 埃左德沖擊試驗 loop tenacity 環結強度 
martens heat distortion temperature test 馬頓斯耐熱試驗 
martensite 馬氏體 mullen bursting strength tester 密廉式破裂強度試驗機 
nol ring test 諾爾環試驗 normal distribution 常態分配 
ozone resistance test 抗臭氧試驗 pareto diagram 柏拉圖 
peeling test 剝離試驗 pinhole test 針孔試驗機 
rattler test 磨耗試驗 rockweel hardness test 洛氏硬度試驗 
rockweel hardness 洛氏威爾硬度 rolinx process 羅林克斯射出壓縮成形法 
rossi-peakes flow test 羅西皮克斯流動試驗 sampling inspection 抽樣檢查 
scratch hardness 抗刮硬度 shore hardness 蕭氏硬度 
spiral flow test 螺旋流動試驗 surface abrasion test 表面磨耗試驗 
taber abraser 泰伯磨耗試驗機 tensile impact test 拉伸沖擊試驗 
tensile strength 抗拉強度 tension test 張力試驗 
thermal shock test 冷熱劇變試驗 torsion test 扭曲試驗 
ubbelohde viscometer 烏別洛德黏度計 vicat indentation test 維卡針壓陷試驗 
Vickers hardness test 維氏硬度試驗 warpage test 翹曲試驗 
weatherometer 人工老化試驗機 weissenberg effect 威森伯格回轉效應

砂輪用語 
abrasive 砂輪 Al2O3 氧化鋁 
balance 平衡 bond 結合 
borazon 氧化硼立方晶 buffing wheel 拋光布輪 
diamond 鉆石 dresser 砂輪整修機 
dressing 修整 endless grinding belt 循環式研磨帶 
finishing allowance 加工余量 grain 磨粒 
grinding disc 研磨盤 jamp up 孔眼堵塞 
mesh 網篩目 parameter 參數 
resinoid grinding wheel 半樹脂型砂輪 slitting 切縫量 
vitrified 陶瓷的 wheel 旋轉

機械設計及周邊其他用語 
assembly drawing 裝配圖 auto tool change cycle 自動換刀時間周期 
beam 橫梁 bending moment 彎矩 
bending stress 彎曲應力 bottoming 底靠 
buckling 縱彎曲 chamfering 去角斜切 
channel 凹槽 chattering 顫動 
check point 查核點 chip 切屑 
chip conveyor 排屑輸送機 coefficient of friction 摩擦系數 
compact 小型的 cooling pipe 冷卻管 
coupon 試樣胚 deflection 撓曲量 
distortion 扭曲變形 draft taper 拔模錐度 
draw out 拉拔 fit tolerance 配合公差 
flexible rigidity 彎曲剛性 gas vent 氣孔 
hatching 剖面線 heater cooler 加熱器冷卻裝置 
hook cavity 鉤穴 inching 寸動 
lug 凸緣 maintenance 維修保固 
metallurgy 冶金學 notch effect 切口效果 
out of roughness 真圓度 performance 動作性能 
pit 坑 plane strain 倒角應力 
plug mill 蕊棒軋管機 
repeated load 重覆載荷 
riveted joint ?釘接合 
sand paper 砂紙 
shift 偏移 
shrink fit 熱壓配合 
shrinkage hole 縮孔 
sinking 凹陷 
sketch 草圖 
spalling 剝落 
straightness 直度 
submarine 深陷式 
surface roughness 表面粗度 
tapping 攻螺絲 
thermocouple 熱電耦 
torsion load 扭轉載荷 
toughness 韌性 
tracing 描圖 
under cut 凹割

3D coordinate measurement 三次元量床 
3D modeling 三次元模擬 
aberration 色差 
abnormal glow 不規則輝光放電 
abrasive 砂輪 
access 通路 
account 帳戶 
accretion 爐瘤 
accurate die casting 精密壓鑄 
acid converter 酸性轉爐 
acid lining cupola 酸性熔鐵爐 
acid open-hearth furnance 酸性平爐 
activator 活化劑 
acetylene 乙炔 
adjustable spanner 活動扳手 
aerator 松砂機 
after service 售後服務 
age hardening 時效硬化 
ageing 老化處理 
air hardening 氣體硬化 
airless plasting cleaning 離心噴光 
air patenting 空氣韌化 
air permeability test 透氣性試驗 
air set mold 常溫自硬鑄模 
air vent valve 通氣閥 
all core molding 集合式鑄模 
alloy tool steel 合金工具鋼 
allround die holder 通用模型 
aluminium alloy 鋁合金鋼 
amendment 修正 
ampere 電流安培 
anchor pin 錨梢 
angle cutter 角銑刀 
angle welding 角焊 
angular pin 角梢 
angular pin 傾斜梢 
animation 卡通影片 
anode effect 陽極效應 
annealing 退火

               朗頓翻譯收集整理詞匯，任何單位和個人未經許可不得轉載，違者必究！